What You Need To Know About Encryption With V6R1
IBM clearly understands that drive based encryption is not suitable for all users due to the complexity and costs associated with it. For more details, see our article ‘LTO4 with Encryption – Why it might not be what you expect.’ Due to the pressure that is now being put on organizations to secure all sensitive data, and particularly the requirements to meet PCI DSS, meant that IBM needed to look for other ways to help users meet their needs.
V6R1 is the first release of i5OS to offer built-in software tape encryption and many people have understandably held off from making a decision on how to encrypt their sensitive data being written to tape until the implications of V6R1 were known.
V6R1 also offers file level encryption on the disk storage and this may lead people to believe that this is the "total solution" they are looking for.
As with all software based encryption throughput always need consideration. First it should be understood that the system processor is not specifically designed to run encryption algorithms and these by their very nature are complex processor intensive operations. In their presentations IBM has quoted a maximum of 75 Mb/sec on a P5 processor and 130 Mb/sec or less on the P6 processor. The encryption algorithms available are AES-128, AES-196 or AES-265, but IBM did not make it clear which of these the figures pertain. If these were with AES-128 you could sensible expect them to halve running AES-256. In any case this was presumably with no other system processes being run at the same time.
IBM also pointed out that the encrypted data will not be compressible on the drive because of the very random data patterns therefore the drives will only run at their native throughput. IBM gave the examples of 40Mb/sec on a 3592 Model 01A and 80 Mb/sec on the 3580 model 003 but of course this is simply the max true drive speed and even that does not take into account command overheads and similar issues that will further slow the throughput.
IBM also gave examples of the impact of their software encryption with different file types with little or no impact on a 1GB source file which is already very slow but also showed around a fifty percent slowdown doing a 64GB and 320 GB large file. Unfortunately they did not share with the audience which encryption method they tested with so care should be taken in case this was done with AES-128.
When asked about restore times there were unable to give an informative response and indicated they had no test figures to share with us. It is normally assumed that a restore will be slower than the save so you might expect this to also be true with the encrypted data being decrypted during a restore.
One of the often heard comments about the LTO-4 tape encryption was that it was difficult to configure and even more difficult to understand. So how does the V6R1 tape encryption option stack up in this area? Well the good news is that it is both easier to configure and to understand, but the bad news is that it is still not simple and straightforward.
To use V6R1 tape encryption users will need a Tape Management Application. IBM is recommending BRMS with the advanced option. Customers must also purchase the Encryption Enablement Option. If you are already a confident BRMS user then adding the encryption will not be as steep of a learning curve as those users who don’t have a background in BRMS.
The V6R1 tape encryption option cannot encrypt everything to tape and specifically excludes *SAVSYS, *SAVSECDTA, *SAVCFG, *IBM, and libraries starting with a Q. Remember that user objects are in QGPL and QUSRSYS. This means that restores of a complete system really do have to be done in a very controlled and structured way to ensure everything runs as planned.
Key management is via multiple layers of protection. The key store file is protected by the master key which is protected by the save / restore key. The keys stores need to be backed up separately to ensure the restore is possible. IBM points out that if the key store file is lost then the data is unrecoverable. Users need to ensure they understand the importance of having good backups of the key store file.
As stated earlier IBM is warning users that the tape drives will not compress the encrypted data so this will slow down the maximum drive speeds to their native throughputs, but this will also mean the amount of tape being used will increase.
For many users this increase in tape utilization will have no discernable impact; however users with lower capacity drives such as the 3590E might need to consider what impact it may have on them. For some people already spanning across say eight tapes, a thirty percent increase in tape utilization may take them over the number of tapes contained in their autoloader resulting in a rethink of their previously unattended overnight backup.
Other New Features
Under V6R1 IBM has introduced the ability to use a Fibre Channel connected tape to do an alternate IPL while previously this was only available with SCSI tapes. This would appear to be restricted to the new 5749 and 5774 fibre channel feature cards initially but this will perhaps also be available on other FC cards. This means a full system restore can now been done quickly and efficiently from FC tape but unfortunately not from an encrypted tape! Because of the previously mentioned restrictions on the ability to run certain backup procedures, specifically a *SAVSYS, these cannot be used to IPL from.
IBM has also added the ability to encrypt each file using a different key. Exactly why this was considered as something that users might want was not made clear. What was made clear was this would have a considerable impact on save times so you should consider the use of this option very carefully.
In a true disaster recovery situation the system is first be restored on the DR server and all the non-encrypted files restored. Once this has been done the BRMS can be configured and set up with the correct key database and then the user can start to begin the restore of their encrypted data from tape. Clearly all companies should be running regular DR exercises to test and hone their DR policy but these needs to be given greater emphasis regarding V6R1 tape encryption configurations. This will also be the time to check the impact on restore times and ensure these still meet the SLAs in place. When using an external DR company it is suggested they are included in the discussions to ensure they have the correct levels of extra hardware to meet the needs.
Users will need to consider the extra costs of BRMS when budgeting for using tape encryption and they need to have the Advanced Option on top of the BASE version of BRMS. You should also look at you existing tape utilization and taking into account the loss of drive compression look at whether or not you need to plan for extra tapes as part of the implementation. For those companies not already using BRMS it is suggested that you include some training in BRMS for those members of staff entrusted in implementing the encryption.
Tape encryption under V6R1 is a big improvement as compared with the LTO-4 or TS1120 drives and EKM as far as complexity and ease of understanding but has all the standard problems and disadvantages as any other software solution. The major issues are the speed, complexity, and the extra complications regarding the restrictions on *SAVSYS, *SAVSECDTA, *SAVCFG, *IBM, or to backup libraries starting with a Q. Costs
Software is often a low cost solution, and dependent on the OS being used.
Hardware is normally the same cost whatever the OS.
Contact us at 866-865-5250 or for a free 30-day trial or for more information.